+91 97253 36833info@cnc-shopfloor.com Exporting Anywhere in the WorldWe deal under NDA
Home About Services Industries Gallery Capabilities FAQ Blog Contact Request a quote
Home / Blog / Surface Finishes for CNC Parts: Anodizing, Plating & More
Insights · 18 Nov 2026

Surface Finishes for CNC Machined Parts: A Practical Guide

A machined part is often not finished when it comes off the CNC machine. Many parts get a surface treatment that protects them from corrosion, makes them harder wearing, changes their colour or makes them easier to clean. Choosing the right finish, and specifying it clearly, is as important as choosing the right material.

This guide covers the most common finishes for CNC machined parts, what each one does, which materials it suits and what to write on your drawing so you get exactly what you need.

Start with the as-machined finish

The as-machined finish is the surface left by the cutting tool. On a typical CNC part it is around Ra 3.2 µm, with light tool marks visible. Finer machined finishes such as Ra 1.6 µm or Ra 0.8 µm are possible with extra finishing passes. For many internal and functional parts, no further treatment is needed at all, which is the cheapest and fastest option.

Two simple mechanical finishes are often used on their own or before another treatment:

  • Bead blasting sprays fine glass or ceramic beads at the part to give an even, matte surface that hides tool marks. It is very common before anodizing for a uniform look.
  • Tumbling and deburring remove sharp edges and burrs, and give small parts a smoother, more consistent surface.

Finishes at a glance

FinishSuitsMain benefitTypical thickness
Anodizing (Type II)AluminiumCorrosion protection, coloursAbout 5–25 µm
Hard anodizing (Type III)AluminiumWear and abrasion resistanceAbout 25–75 µm
Chromate conversion (chem film)AluminiumCorrosion protection while staying electrically conductiveUnder 1 µm
PassivationStainless steelRestores corrosion resistance after machiningNo measurable change
ElectropolishingStainless steelSmooth, bright, easy-to-clean surfaceRemoves a few µm
Zinc platingCarbon and alloy steelLow-cost corrosion protectionAbout 5–25 µm
Electroless nickelSteel, aluminium, brassEven coating in bores and corners, wear and corrosion resistanceAbout 5–25 µm
Black oxideSteelBlack appearance, mild protection when oiledAround 1 µm
Powder coatingMost metalsTough, decorative coating in many coloursAbout 50–120 µm

Thicknesses are typical ranges. The exact value depends on the process, the specification and the class you call out, so always confirm with your supplier.

Finishes for aluminium

Anodizing (Type II)

Anodizing is an electrochemical process that grows a hard oxide layer on the aluminium itself, rather than adding a separate coating on top. Type II (sulphuric acid) anodizing is the most common finish for aluminium parts. It improves corrosion resistance, and the porous layer can be dyed black, red, blue, gold and many other colours before it is sealed. Clear anodizing keeps the natural metal look.

Points to know:

  • The anodized layer is electrically insulating. Mask any surface that must make electrical contact, such as earthing points.
  • Roughly half of the layer grows outward from the original surface. Holes get slightly smaller and outside dimensions slightly larger.
  • Colour can vary slightly between alloys and between batches. If colour matching matters, say so and keep the same alloy for all parts.
  • Common specifications are MIL-A-8625 and ISO 7599.

Hard anodizing (Type III)

Hard anodizing uses a colder bath and higher current to grow a thicker, much harder layer. It is used for sliding parts, pistons, guides and anything exposed to wear. The natural colour is dark grey to bronze, depending on the alloy, and it is often dyed black. Because the layer is thick, tolerances on critical features must take the build-up into account. The common specifications are MIL-A-8625 Type III and ISO 10074.

Chromate conversion coating (chem film)

Also known by trade names such as Alodine or Iridite, this is a very thin chemical coating that protects aluminium from corrosion and makes a good base for paint, while the surface stays electrically conductive. That makes it popular for electronics housings and earthing points. For parts going into the European market, ask for a trivalent (RoHS-compliant) chromate rather than the older hexavalent type.

Finishes for stainless steel

Passivation

Stainless steel resists corrosion because of a thin, invisible chromium oxide layer on its surface. Machining can leave tiny particles of free iron from tools on the part, which can later show up as rust spots. Passivation is a chemical treatment, usually with nitric or citric acid, that removes this free iron and helps the protective layer re-form. It does not change the look or the dimensions of the part. Common specifications are ASTM A967 and ASTM A380.

Electropolishing

Electropolishing removes a very thin layer of metal electrochemically, smoothing out microscopic peaks. The result is a bright, smooth surface that is easier to clean and more corrosion resistant. It is widely used for food processing, pharmaceutical and medical parts. Because it removes material, it should be allowed for on very tight tolerances.

Finishes for carbon and alloy steel

Zinc plating

Zinc plating is the most common low-cost corrosion protection for steel parts such as brackets, fasteners and housings. A passivate layer on top gives a clear (silver-blue), yellow or black appearance. ISO 2081 is a common specification. For high-strength or hardened steels, ask about hydrogen embrittlement relief (baking after plating), because plating can make these steels brittle if this step is skipped.

Electroless nickel

Unlike electroplating, electroless nickel is deposited by a chemical reaction rather than an electric current. That means it builds up at the same thickness in holes, bores and corners as on the outside, which makes it a good choice for complex parts with tight tolerances. It gives good wear and corrosion resistance and can be used on steel, aluminium, copper and brass. ASTM B733 is a common specification.

Black oxide

Black oxide converts the surface of steel into a thin black layer. It adds almost no thickness, so it suits precise parts such as tooling, fixtures and gun-metal coloured components. On its own it offers little corrosion protection. It is normally sealed with oil or wax, and is best for parts used indoors.

Hard chrome plating

Hard chrome gives a very hard, low-friction surface for hydraulic rods, shafts and moulds. It is usually plated slightly oversize and then ground to the final dimension.

Powder coating and painting

Powder coating sprays a dry powder onto the part and then bakes it into a tough, even layer. It comes in almost any colour and in matte, satin or gloss. It is ideal for enclosures, frames and visible parts. Because it is thick, threads, fitting holes and mating faces normally need to be masked. Wet painting is an alternative when a specific colour, small batch or very thin coat is needed.

How to choose a finish

  • Outdoor or wet environment: anodizing for aluminium, passivation or electropolishing for stainless steel, zinc plating, electroless nickel or powder coating for steel.
  • Wear and sliding contact: hard anodizing, electroless nickel or hard chrome.
  • Electrical contact or earthing: chromate conversion coating, or mask those areas before anodizing.
  • Food, medical or hygienic use: electropolished or passivated stainless steel.
  • Appearance and colour: anodizing for aluminium, powder coating for most metals.
  • Lowest cost: as-machined or bead blasted, if the material is already suitable for the environment.

The choice of material and finish go together. Our guide to choosing a material for CNC parts covers the material side.

What to put on your drawing

  • Name the process and the specification, for example "Anodize per MIL-A-8625 Type II, Class 2, black" or "Zinc plate per ISO 2081, clear passivate".
  • Give the thickness or class where it matters.
  • Mark masked areas such as threads, bearing bores and electrical contact points.
  • Say whether dimensions apply before or after finishing. This is critical for tight tolerances. Our guide to CNC machining tolerances explains why.
  • Add appearance requirements if cosmetic surfaces matter, for example "bead blast before anodize, no visible tool marks on face A".
  • State compliance needs such as RoHS or REACH for parts going to Europe.

Conclusion

The right surface finish protects your parts, extends their life and makes them look the way you intended. Pick the finish based on the environment, wear, electrical needs and appearance, then specify it clearly with the standard, thickness and masking. If you are not sure which finish suits your part, send us the drawing. Our CNC machining services team can suggest a suitable finish when we quote, and all work is under NDA. Request a quote.

FAQ

What is the best surface finish for aluminium CNC parts?
For most aluminium parts, Type II anodizing is the standard choice. It improves corrosion resistance and can be dyed in many colours. Hard anodizing (Type III) is better for wear, and chromate conversion coating is used where the surface must stay electrically conductive.
Does anodizing change the dimensions of a part?
Yes, slightly. Roughly half of the anodized layer grows outward from the original surface, so holes get a little smaller and outside dimensions a little larger. For tight tolerances, state whether dimensions apply before or after anodizing, or mask the critical features.
What is the difference between passivation and electropolishing?
Passivation is a chemical treatment that removes free iron from stainless steel and restores its corrosion resistance without changing its look or size. Electropolishing removes a very thin layer of metal to give a bright, smooth, easy-to-clean surface, and also improves corrosion resistance.

Have a part to make? Let's talk.

Request a quote